SPECIFICATION 
規格書
					 | 
				
				
					| 
						Designation 品名:
					 | 
					
						DC POWER JACK
					 | 
				
				
					| 
						Model No. 型 號:
					 | 
					
						DC-055B
					 | 
				
				
					| 
						1. Rating額定值:
					 | 
					
						DC 30V  0.5A
					 | 
				
				
					| 
						2. Operation temperature range 使用溫度範圍:
					 | 
					
						-20℃~+70℃
					 | 
				
				
					| 
						3. Preservative temperature range 保存溫度範圍:
					 | 
					
						-40℃~+85℃
					 | 
				
				
					| 
						4. Construction dimension 結構尺寸:
					 | 
					
						Apply to the appended drawing: 符合附加圖紙
					 | 
				
				
					| 
						Item 項目
					 | 
					
						Test condition 測試條件
					 | 
					
						Specification規格
					 | 
				
				
					| 
						5. Electrical characteristics電氣性能
					 | 
				
				
					| 
						5A
					 | 
					
						Contact  
Resistance 
接觸阻抗
					 | 
					
						Being measured at 1KHz small current  
contact resistance meter. 
在1KHZ小電流下測量.
					 | 
					
						30mΩ max. 
30毫歐以下.
					 | 
				
				
					| 
						5B
					 | 
					
						Insulation 
 Resistance 
絕緣阻抗
					 | 
					
						Measurements shall be made following  
application of DC 250V potential across 
 terminals and across terminals  
and frame for 1 minute. 
在端子之間和端子與殼之間加DC 250V條件下, 
持續1分鐘測量.
					 | 
					
						100MΩ min. 
100兆歐以上.
					 | 
				
				
					| 
						5C
					 | 
					
						Withstand  
Voltage 
耐電壓
					 | 
					
						AC 500V (50Hz or 60Hz) shall be applied 
across terminals and across terminals 
and frame for one minute. 
在端子之間和端子與殼之間加AC 500V 
(50HZ或60HZ)條件下,持續1分鐘測量.
					 | 
					
						There shall be no breakdown. 
無擊穿現象出現.
					 | 
				
				
					| 
						6. Mechanical characteristics 機械性能
					 | 
				
				
					| 
						6A
					 | 
					
						Insertion and  
Extraction force  
插拔力
					 | 
					
						Being measure at across spring piece  
and across matching plug for ergometer. 
用測力計在插頭與彈片之間進行測量.
					 | 
					
						Insertion and extraction force: 3~25N 
插拔力: 3~25N
					 | 
				
				
					| 
						6B
					 | 
					
						Terminal 
 Strength 
端子強度
					 | 
					
						A static force of 5N being applied in one  
direction on the tip of terminal for 10sec. 
將5N之靜負荷施加於端子頂部的一個方向 
持續10秒。
					 | 
					
						(1). Contact resistance:50mΩmax. 
接觸阻抗:50毫歐以下. 
(2). Insertion and withdraw force: 3~25N 
插入力和拔出力:3~25N 
(3). Electrical characteristics and  
mechanical characteristics shall  
be satisfied. Without distinct damage. 
機械,電氣性能滿足規定要求,無異常發生
					 | 
				
				
					| 
						7. Durability 耐久性
					 | 
				
				
					| 
						7A
					 | 
					
						Soldering test 
可焊性試驗
					 | 
					
						The tip of the terminals shall be dipped 
2mm in the solder bath 
 at a temperature of 240±5℃ for 3±0.5sec. 
端子頂部被浸入焊錫池2mm深,溫度240±5℃, 
時間3±0.5秒。
					 | 
					
						A new uniform coating of solder shall  
cover a minimum of 95% of the surface 
 being immersed. 
浸入的部分95%以上表面將被錫覆蓋.
					 | 
				
				
					| 
						7B
					 | 
					
						Resistance to  
soldering heat 
耐焊接熱
					 | 
					
						The jack shall be put into at the temperature 
of 250±5℃ in 5±1sec(Automatic soldering)  
or 380±5℃ in 3±1sec(Manual soldering)  
after which measurement shall be made. 
將產品端子浸入錫爐, 250±5℃,5±1秒 
(自動焊);380±5℃,3±1秒(手工焊)
					 | 
					
						(1). Contact resistance:50mΩmax. 
接觸阻抗:50毫歐以下. 
(2). Insertion and withdraw force: 3~25N 
插入力和拔出力:3~25N 
(3). Electrical characteristics and 
mechanical characteristics shall be 
satisfied. Without distinct damage. 
機械,電氣性能滿足規定要求,無異常發生
					 | 
				
				
					
						Remark 
備 註
					 | 
					
						G-Switch 東莞品贊電子科技有限公司
					 |