G-Switch 東莞品贊電子科技有限公司
SPECIFICATION
規格書
Designation 品名:
USB插座
Model No. 型 號:
MICRO USB 5P
1. Rating額定值:
DC 48V 0.2A
2. Operation temperature range 使用溫度範圍:
-20℃~+70℃
3. Preservative temperature range 保存溫度範圍:
4. Construction dimension
結構尺寸:
Apply to the appended drawing:
符合附加圖紙
Item 項目
Test condition 測試條件
Specification規格
5. Electrical characteristics電氣性能
5A
Contact Resistance
接觸阻抗
Being measured at 1KHz small current
contact esistance meter.
在1KHZ小電流下測量.
30mΩ max.
30毫歐以下.
5B
Insulation Resistance
絕緣阻抗
APPLY A VOLTAGE OF 500V DC FOR 1 MIN. TO
FOLLOWING PORTIONS AFTER WHICH
MEASUREMENT SHALL BE MADE:
（1） BETWEEN BODY AND CONDUCTOR
（2） BETWWEN CONDUCTORS NOT TO BE
CONTACT
輸入：500V DC 電壓１分鐘，按以下接觸方法測試：
（1）接觸端子之間
（2）膠座與排腳之間
100MΩ min.
100兆歐以上.
5C
Withstand Voltage
耐電壓
AC AC 500V IMS(50Hz) FOR 1 MIN TRIP CURRENT:
0.5mA
（1）BETWEEN BODY AND CONDOCTOR
（2） BETWEEN CONDUCTORS NOT TO BE CONTACT
輸入AC 500V(50HZ)電壓，１分鐘感應電流0.5ｍＡ，接以
下接觸方法測試：
（１）排腳相互之間
（２）排腳與外殼之間
WITHOUT DAMAGE TO
PARTS ARCING OR
BREAKOOWN ETC
沒有絕緣破壞等異常
6. Mechanical characteristics 機械性能
6A
Insertion and
Extraction force
插拔力
插入力度：
MEASUREMENT SHALL BE MADE AFTER
CONNECTING AND DISCONNECTING USING
STANDARD PLUG GAUGE 3 TIMES.
依據標準的PLUG GAUGE 做出３次撥插后測定
拔出力度：
MEASUREMENT SHALL BE MADE AFTER
CONNECTING AND DISCONNECTING USING
STANDARD PLUG GAUGE 3 TIMES.
依據標準的PLUG GAUGE 做出３次撥插后測定
（0.7kg~4kg）
6B
Terminal Strength
端子強度
A STATIC LOAD OF (300gf)SHALL BE APPLIED
TO THE TIP OF TERMINAL FOR 1MIN. IN ANY
DIRECTION.
在任意一個方向的先端加上（300gf）力度測，時間為
1 分鐘。
THERE SHALL BE NO DAMAGE
TO THE TERMINAL SUCH AS
CRACKS, LOOSENESS OA PLAY
ELECTRICAL AND MECHANICAL
CHARACTERISTICS SHALL BE
SATISFIED
在排腳中沒有裂開，松動等異常。
滿足于機械，電氣性能。
7. Durability 耐久性
7A
Soldering test
可焊性試驗
THE TOP OF THE TERMINALS SHALL BE DIPPED
2mm IN THE SOLDER BATH OF 230±5℃ FOR
3±0.5 SECONDS.
端子頂部被浸入錫焊池中1mm 深，溫
度為230±5℃，時間為3±0.5 秒。
THE AREA OF SOLDERING.
SHOULD BE OVER 75%.
焊接面積要有75%以上。
7B
Resistance to
soldering heat
耐焊接熱
SOLDER BATH METHOD:
SOLDER TEMPERATURE 260±5℃ IMMERSION
TIME 3±0.5 SEC IMMERSION DEPTH UP TO THE
SURFACE OF THE BOARD THICKNESS OF
PRINTED WIRING BOARD 1.6mm DIMENSIONS
OF COMPONENT HOLES IN THE PRINTED
WIRING BOARD SHALLBEING ACCORDANCE
WITH THOSE
SPECIFIED IN THIS SPECIFICATION.
焊爐焊接的時候溫度控制在260±5℃，過
爐時間3±0.5 秒，于（基板）厚度為1.6mm
WITHOUT DEFORMATION OF
CASE OR EXCESSTVE
LOOSENESS OF TEMINALS
ELEXTRICAL
CHARACTERISTICS SHALL BE
SATISFIED.
本體無變形、能滿足于機械、電氣
性能。
Remark
備 註
G-Switch 東莞品贊電子科技有限公司
Designation 品名:
USB插座
Model No. 型 號:
MICRO USB 5P
Item 項目
Test condition 測試條件
Specification規格
7C
Life test
壽命試驗
WITHOUT LOAD:
CONNECTION AND DISCONNECTION SHALL
BE MADE WITH THE MATING PLUGS AND
JACKS FOR 10,000 CYCLES AT A SPEED OF 15
TO 18CYCLES/MIN.
無負荷：將結合了的標準（盡量要近于中心點）在1
分鐘內以15~18 的速度，進行10,000 次
插入、撥出。
(1) CONTACT RESISTANCE SHALL
BE 200m MAX.
(2) MECHANICAL AND
ELECTRICAL
CHARACTERISTICS SHALL BE
SATISFIED.
(1)接觸電阻不能超于200m。
(2)其他、滿足于機械、電氣性能。
7D
Heat test
耐熱試驗
THE JACK SHALL BE STORED AT A
TEMPERATURE OF 85±2℃ FOR 96 HOURS
AND THEN IT SHALL BE SUBJECTED TO THE
CONTROLLED RECOVERY CONDITIONS FOR
1 HOUR AFTER WHICH MEASUREMENT SHALL
BE MADE.
放置在溫度85±2℃中測試96 小時后，再放置正常
室溫中1 小時來測定。
(1). Contact resistance: 30mΩmax.
接觸電阻:30毫歐以下
(2). Insulation resistance: 100MΩmin.
絕緣電阻: 100兆歐以上
(3). There shall be no sign of damage
mechanically and electrically.
無任何跡象顯示機械及電器性能之損壞.
7E
Humidity test.
耐濕試驗
THE JACK SHALL BE STORED AT A
TEMPERATURE OF 40±2℃ AND A HUMIDITY
OF 90% TO 96% FOR 96 Hr THEN THE JACK
SHALL BE MAINTAINED AT STANDARD
ATMOSPHERIC CONDITION FOR 1 Hr FOR
OTHER PROCEDURES.
放置40±2℃，的相對溫度為90~96%Hr 環境中96
小時后，再將樣板放在正常環境１小時后進行測試
7F
Cold test
耐寒試驗
At –40±2℃ for 96 hours, after test keep
in normal condition for 30 minutes.
在-40±2℃環境中放96小時,再置於
正常環境中30分鐘後進行測試.
7G
RESISTANCE
SALT SPRAY
TEST
耐鹽霧性試驗
CONNECTOR AT THE CONNENTRATION OF 5±
1% OF THE SALT WATER,AMBIENT
TEMPERATURE:35±2°C ,SPRAY 12 HOURS AFTER
REMOVAL,CLEAN WATER,DRIED MEET.
連接器放置在濃度為5±1%的鹽水中，溫度為35±2°C
的實驗箱內，噴霧12 小時后取出，用水清洗，晾干滿
足
IN THE ABSENCE OF METAL
CORROSION,COATING REVIEW
AREA OF MORE THAN 80
PERCENT
外觀 基體金屬無銹蝕，鍍層覆面
80%以上。
8. Standard condition 試驗、測定狀態
UNLESS OTHERWISE SPECIFIED THE
STANDARD RANCE OF ATMOSPHERIC
CONDITIONS FOR MAKING MEASUREMENTS
AND TESTS ARE AE FOLLOWS:
(1) AMBIENT TEMPERATURE : 5℃ TO 35℃
(2) RELATIVE HUMIDITY : 45% TO 85%
(3) AIR PRESURE : 80Kpa TO 106Kpa
在沒有指定的情況下測試溫度、濕度、氣壓如下：
(1) 溫度為 5℃~ 35℃
(2) 濕度為 45%~ 85%
(3) 氣壓為 80Kpa~ 106Kpa
Remark
備 註
G-Switch 東莞品贊電子科技有限公司
